Charging Pile Monitoring Module Faults and Troubleshooting

Below is a look at common charging pile monitoring module fault analysis and troubleshooting methods.

Charging Station Module

Monitoring Module Parameters Cannot Be Set

  • The monitoring module cannot communicate with the downstream device, resulting in the inability to set parameters.
  • An incorrect configuration will also cause the monitoring module parameters to be unconfigurable.
  • Parameters exceeding limits will prevent parameter setting.

Monitoring Module Fault – Buzzer Does Not Sound

  • Buzzer Fault: Setting the buzzer to mute in the monitoring module will result in the buzzer not sounding (but the fault light will illuminate).

Monitoring Module Does Not Control Equalizing Charge State

  • Critical faults such as module communication interruption, AC power failure, or battery pack branch circuit break will cause the monitoring module to enter fault protection state and not switch to equalizing charge.
  • Battery current detection errors will prevent the monitoring module from entering equalizing charge state.
  • Manual mode will not automatically enter equalizing charge; a manual setting is required to enter equalizing charge.

Monitoring Module Displays Incorrect Battery Capacity

  • Battery current detection error.
  • Equalizing charge must be enabled to ensure battery capacity calibration.

Alarm Handling

  • The monitoring module categorizes alarms into four levels: Critical Alarm, Emergency Alarm, General Alarm, and No Alarm.
  • Critical/Emergency Alarms: These alarms severely impact the power system’s performance. Regardless of when they occur, immediate action from the user is required. The system illuminates the alarm indicator and emits an audible alarm.
  • General Alarms: These alarms allow the power system to temporarily maintain normal DC output. If they occur during shift work hours, immediate action is required. If they occur outside of shift work hours, action should be taken at the start of the shift. The system only illuminates the alarm indicator.
  • No Alarm: If the user has set this type of alarm to “No Alarm,” the system can continue operating normally without any audible or visual indication when this alarm is triggered.

Charging Pile Monitoring Module Faults

Common Alarm Handling Methods

Alarm Name: AC Power Outage
  • Handling Method: For short power outages, DC power is supplied by the battery. If the cause of the outage is unknown or the outage is prolonged, a generator should be started. It is recommended to wait at least 5 minutes after starting the generator before switching power to the mains system to minimize the impact on the power supply equipment during the generator start-up transition.
Alarm Name: AC Overvoltage
  • Handling Method: Check if the setpoint is too low; if so, change it.
  • General overvoltage does not affect system operation. When the mains voltage exceeds 295V, the charging module will stop working. Therefore, for power supply networks with persistent overvoltage, it is necessary to consult with relevant power network maintenance personnel to improve the power grid.
Alarm Name: AC Undervoltage
  • Handling Method: Check if the setpoint is too high; if so, change it.
  • If the mains voltage is below 176V, the charging module will limit power output; below 80V, it will stop working. Therefore, for power supply networks with persistent undervoltage, it is necessary to consult with relevant power network maintenance personnel to improve the power grid.
Alarm Name: Surge Protector Failure
  • Check the surge protector. If it is damaged, replace it.
Alarm Name: DC Overvoltage Alarm
  • Check the DC output voltage and the “DC Overvoltage Alarm” setting on the monitoring module. If the setting is unreasonable, change it.
  • Locate the charging module causing the overvoltage alarm. While ensuring the battery can supply power normally, disconnect the AC input switches of all charging modules. Then, turn on the AC input switches of the modules one by one. When the AC input switch of a certain module is turned on, the system experiences another overvoltage alarm; this module is overvoltage and should be replaced.
Alarm Name: DC Undervoltage Alarm
  • Check the DC output voltage and the “DC Undervoltage Alarm” setting on the monitoring module. If the setting is unreasonable, change it.
  • Check if the mains power is interrupted. If so, disconnect some loads to extend the operating time of the entire power system.
  • Check if any charging modules are not working (i.e., no output current). If so, replace the module.
  • Check the total load current. If the total load current exceeds the total output current of the charging modules during float charging, disconnect some loads or add charging modules so that the total current of the charging modules exceeds the total load current by 120%, and at least one charging module has redundancy.
Alarm Name: Load Branch Open, Battery Branch Open
  • Check if the circuit breaker or fuse for this branch is open (check the position of the circuit breaker handle, or measure the voltage across the fuse; if the voltage is close to 0V, the fuse is normal). If it is open, find the cause and troubleshoot. Otherwise, it indicates a fault in the alarm circuit; please contact Emerson.
Alarm Name: Battery Protection
  • Check if the mains power is interrupted, or if the battery voltage has dropped below the “Battery Protection Voltage” setting, or the discharge time has reached the “Battery Protection Time” setting.
  • Manual Battery Protection Control Required
Alarm Name: Module Failure
  • The red LED on the charging module panel will illuminate. Disconnect the AC input to the charging module and restart it after a period of time. If the alarm persists, replace the module.
Alarm Name: Module Protection
  • Check if the mains voltage is greater than the charging module’s AC overvoltage point (295V) or less than its AC undervoltage point (80V). Therefore, for power supply networks with persistent overvoltage or undervoltage, consult with relevant power network maintenance personnel to improve the power grid.
Alarm Name: Module Fan Failure
  • Check if the charging module’s fan is running. If the fan is not running, check if it is blocked. If blocked, clear it. If it is not blocked or the fan failure persists after clearing, replace the fan.
Alarm Name: Module Communication Interruption
  • Check if the communication connection between the charging module and the monitoring module is normal. If normal, restart the module. If the alarm persists, replace the module.
Alarm Name: High Battery Temperature Alarm
  • Check if an internal battery fault is causing overheating. If so, replace the faulty battery.
  • Check if the battery room temperature is too high. If so, lower the battery room temperature.
Update cookies preferences

Get a Quick Quote!

x

    Get a Quick Quote!

    x