EV charger higher utilization: what is dynamic power sharing

To increase EV charger utilization without wasted power, one solution is a satellite charging system, also known as a charging stack and terminals. It will put all charging modules into a single charging cabinet, which is the input. Several terminals are output. Here, the power can be dynamically allocated to each terminal as per the electric car’s demand. So, what is dynamic power sharing?

For example, the BYD Atto3 battery capacity is 60.48kWh, and it can accept about 90kW charging. Well, the BYD electric bus has a much bigger battery capacity, like 563kWh, and supports 250kW. When 2 cars charge in the same EV charger station, more power will be given to the bus rather than the passenger car because the BYD Atto3 doesn’t have the demand. That is a higher utilization of the EV charger.

Flexible allocation of charging piles

But if you only need one unit of charger and also want to make the EV charger have higher utilization. How to make it. Well, Bluesky has a dynamic power-sharing solution for EV chargers that distributes power to cars based on their demand. When the BYD electric bus and BYD Atto3 charge at the same dual gun 240kW charger station, it is not equally distributed. BYD will only accept 90kW at most, and the other part will go to the BYD electric bus.

Dynamic power sharing: What is the technology point behind the higher utilization of EV chargers?

The key point is the high-voltage contactor, as the picture shows.

High voltage contactor distribution diagram

A high-voltage contactor is common in electric buses, responsible for connecting the battery pack to the motor when startup and disconnecting it when faults occur. It is a kind a switch. So we add it to our charger and update our program to tell this switch when to cut off and when to connect.

The high voltage contactor is connected to the gun and also the wires from the power module. According to our updated program, the high voltage contactor will turn off and disconnect it from the wire from the power module. Thus, the power module will not be distributed to this gun. In this way, dynamic power sharing is achieved.

A high-voltage contactor is an economical scheme. Another is the module switch, which has the same function.

module switch

With dynamic power sharing, higher utilization is achieved. But of course, this solution will be more expensive because not only is it the hard work of our R&D team, but it also requires more manpower and steps in assembly and testing before production is finished. Not to mention the increase in our cost. No power wasted. If you are interested, just email us.

Framework Structure of a Flexible Power Distribution System Based on a Microcontroller

This paper mainly focuses on the AT32F435VGT7 microcontroller, realizing the fabrication of a flexible power distribution control board for charging piles. The main contents are as follows:

  •  Hardware architecture: The AT32F435VGT7 is used as the core, and the peripheral circuits include power management and communication interface modules.
  • Configuration: The State Grid Corporation of China’s electric vehicle charging equipment standard protocol is implemented.
  • CAN bus protocol is used to control multiple charging modules and the switching module; the Xinruida XG070YVW15R touchscreen is used as the human-machine interface.

Based on the design of the DC charging pile power flexible distribution controller, the dynamic adjustment function of charging power is realized. Test results show that the control board can be used for flexible power distribution on 16 charging loops.

System Framework Structure

The control section of the flexible power distribution system uses the AT32 chip, and the information display section uses a touch screen. The FM25L16B-G and W25Q16BVSSI integrated chips are used as the system setting parameter memory and system information data memory, respectively.

System design block diagram

  • Power Supply Circuit: The power supply is DC 12V. An external switching power supply is needed to convert AC 220V to DC 12V, and then a rectifier-step-down circuit is used to obtain DC 3.3V and DC 5V; DC 3.3V supplies power to the main circuit.
  • DS1307 External Clock: An external high-precision 32.768kHz crystal oscillator.
  •  CAN Communication Circuit: The CAN bus uses twisted-pair cable as the primary transmission medium, further enhancing the system’s anti-interference performance.
  • Relay Control Circuit: The relay control circuit mainly controls the on/off states, is simple and reliable, and can isolate high and low voltage currents.
  • Easy to judge and identify, and allows the receiver to quickly know the relevant status information, which is convenient for subsequent circuits to perform corresponding logic processing or control operations.
Update cookies preferences

Get a Quick Quote!

x

    Get a Quick Quote!

    x